MOVE TO NEW HARD DRIVE INSTALL IS TIED
MOVE TO NEW HARD DRIVE FREE VERSION OF

Move To New Hard Drive Install Is Tied

Select your new hard drive. Scroll down and check the 'Hard disk' box near the bottom of the window. This should be your attached hard drive. Also, a Windows install is tied to the hardware in terms of drivers, and switching motherboards means that the current driver set of the install on the HDD is most likely, NOT going to work. So, even if it does boot (which it might not), there is likely to be a problem with activation. Computer Type: PC/Desktop.After a few moments, your system partition will be expanded to include the additional space on your drive, ensuring that all available drive space is usable.

Move To New Hard Drive Free Version Of

When it boots it up, itвЂ™ll start to detect and install all device drivers again. One feature that was useful in Windows versions prior to XP was you could simply take out a hard drive that has Windows installed and connect it up to another computer. Unfortunately, as this process doesnвЂ™t work if youвЂ™re moving from a larger to smaller drive, youвЂ™ll need to use third-party software to copy Windows instead.Various tools exist for this method, but one good (and free) option is to use Macrium Reflect Free. The free version of Macrium Reflect allows you to clone your Windows installation from a larger to a smaller drive, resizing the partition table in the process. You can also use this to clone Windows to a larger driver if youвЂ™d prefer.Before you follow these steps, make sure that both your existing hard drive and new hard drive are connected to your PC and are detectable in Windows.

The only real hope you have of this problem not occurring is to use a motherboard with exactly the same chipset for the hard drive controller.After all these years since the release of Windows XP, itвЂ™s still not a straightforward task to move a Windows XP hard drive and partition to another computer without getting a blue screen. The recovery console or even Safe Mode isnвЂ™t usable because Windows canвЂ™t boot anything without the correct software for the controller. If the old controller uses one driver and the new controller requires a different driver, XP is trying to boot with the old driver and throws up the blue screen because the wrong driver is trying to load. The error will usually be a STOP 7B error which is related to a problem with the hard drive controller.This problem is often simply due to the fact that the storage controller used by Windows XP requires a different driver depending on what type of hard drive controller is on the motherboard.

NET framework 3.5, msxml-4 components, and DirectX-9. Software that functions perfectly well on the old PC, with a fully updated version of XP, wonвЂ™t function on the newer PC where I did a clean install of XP from scratch also adding SP3. Amazingly, a large proportion of websites on the internet (including Microsoft) will tell you the only solution is to perform a Repair Install or even completely wipe your XP install with a format and re-install.The reason for my doing this drive swap is that it seems impossible to arrive at a full copy of XP starting from scratch.

Thanks Microsoft for being so customer orientated. IвЂ™m looking at a solution using safe-mode, and regedit to get back control of my own PC, and software. Any attempt to activate over the internet seems to fail, leaving me with the dubious option of phoning. All the options brought me back to the beginning again, not allowing me to log on to my own computer, despite paying Microsoft for two copies of XP, this, and the one which used to be on the host PC, long gone, which this replaces.

Would absolutely love your advice on this topic. Then the proper drivers could be re-installed. It is astonishing, and also a credit to you, that this simple technique is only available on your blog.However, can you top this by suggesting why, after getting the install to boot fine, I canвЂ™t then go and update the HDC drivers back to the appropriate nVidia nForce 430 drivers as supplied by the motherboardвЂ™s website, without a repeat of the STOP 7B BSOD? I was under the (perhaps misguided) impression that the HDC only needed to be downgraded to the old generic Windows driver in order to get the system running again. Despite the install being less than pristine in state, using this method of switching the hard drive controllerвЂ™s driver, then Parted MagicвЂ™s clone tool, I successfully migrated the install! Thanks for this help. With Seagate SSHD drives dropping to $99 for 500GB, I thought IвЂ™d move that install from a mechanical drive to the SSHD.

The Device Manager (View Devices by connection) displays this tree (IвЂ™ve removed the less relevant entries)HereвЂ™s the board: gigabyte.com.au/products/product-page.aspx?pid=1939#spI donвЂ™t have any single other ATA/IDE device installed, not even an optical drive.2) I have run the driver installer downloaded from the GigaByte page above. Just to get this really straight in my head вЂ¦1) My existing XP install is running on a single-partitioned standard SATA HDD. IвЂ™m just fascinated by this issue. IвЂ™m not trying to ask for specific help here so if you donвЂ™t want to supply that, I understand. Thanks for the ongoing discussion. I know my old motherboard canвЂ™t run the SSHD in itвЂ™s optimal SATA3 (600 MB/s) mode but I have it plugged into a SATA2 port so IвЂ™d hope SATA2 speeds of 300MB/s would be (theoretically) attainable.Hi.

Move Windows 10 To New Hard Drive